Difference between revisions of "Dante"
| Line 1: | Line 1: | ||
| − | See [[Yamaha Tio1608-D|Yamaha]] for an example | + | See [[Yamaha Tio1608-D|Yamaha Tio1608-D]] page for an example |
| − | == | + | == CONFIGURATION == |
| + | - AES67 clocking on both Dante and SOUND4 | ||
| − | ==== S4->Dante ==== | + | - select "SAP Advertising" on SOUND4 |
| + | |||
| + | - Some DANTE devices accept only 1ms packets, L24 (L16 is accepted but does not work : noise). This is the "AES67 Low Latency (Standard)" audio Profile. You may try the "AES67 Very Low Latency" profile with 250µs packets. | ||
| + | |||
| + | - VLAN : if no VLAN, use default AES67 profiles : No 802.1 tagging. Else must change AES67 Profiles configuration | ||
| + | <br /> | ||
| + | |||
| + | === For Dante to SOUND4 === | ||
| + | Normally just select session from list. | ||
| + | |||
| + | Manual setting : | ||
| + | |||
| + | - on Dante source device you have to retrieve the Multicast IP address of the stream (something like 239.x.y.z). Also try to get the port, it is usually 5004 | ||
| + | |||
| + | - on SOUND4 you have to select AES67, and write down the IP address in the "Session" field, with port if not 5004 (eg "239.193.4.68:5004") | ||
| + | |||
| + | - two new fields appear that has to be configured according to stream config : "Sample Format" (usually "L24") and "Nb Channels" (usually 2 ; if the stream has more than 2 only the first two will be used) | ||
| + | |||
| + | You should now receive it | ||
| + | |||
| + | === For SOUND4 to Dante : === | ||
| + | - on SOUND4, select "AES67 Low Latency (Standard)" and chose a Multicast IP address that is free. Default port is 5004 if not given | ||
| + | |||
| + | - Check Stream format in Advanced/AES67 Profiles for "Sample Format" (normally L24) and "Nb Channels" (normally 2) | ||
| + | |||
| + | - stream should appear on Dante Controller, with a "+" drop-down to select channels. If no "+", SDP is not recognised. | ||
| + | |||
| + | - on Dante sink device you normally just have to configure this address and port if requested. | ||
| + | |||
| + | Note : | ||
| + | |||
| + | - Dante Controller only used for connection. Dante device is then "subscribed" to the stream (to the Mcast IP address) forever (no need Controller afterwards). | ||
| + | <br /> | ||
| + | |||
| + | == Tools == | ||
| + | |||
| + | === RAV2SAP === | ||
| + | Translate Ravenna mDNS <=> Dante SAP | ||
| + | |||
| + | May be used to diagnose advertisement problems (SDP SAP) | ||
| + | |||
| + | https://www.ravenna-network.com/aes67/rav2sap/ | ||
| + | ==Troubleshooting== | ||
| + | |||
| + | ====S4->Dante==== | ||
Advertised (checkmark under Dante Controller) but no sound (HP greyed) : check clock is AES67. If clock not synched, no sound. | Advertised (checkmark under Dante Controller) but no sound (HP greyed) : check clock is AES67. If clock not synched, no sound. | ||
Revision as of 16:56, 22 February 2021
See Yamaha Tio1608-D page for an example
Contents
CONFIGURATION
- AES67 clocking on both Dante and SOUND4
- select "SAP Advertising" on SOUND4
- Some DANTE devices accept only 1ms packets, L24 (L16 is accepted but does not work : noise). This is the "AES67 Low Latency (Standard)" audio Profile. You may try the "AES67 Very Low Latency" profile with 250µs packets.
- VLAN : if no VLAN, use default AES67 profiles : No 802.1 tagging. Else must change AES67 Profiles configuration
For Dante to SOUND4
Normally just select session from list.
Manual setting :
- on Dante source device you have to retrieve the Multicast IP address of the stream (something like 239.x.y.z). Also try to get the port, it is usually 5004
- on SOUND4 you have to select AES67, and write down the IP address in the "Session" field, with port if not 5004 (eg "239.193.4.68:5004")
- two new fields appear that has to be configured according to stream config : "Sample Format" (usually "L24") and "Nb Channels" (usually 2 ; if the stream has more than 2 only the first two will be used)
You should now receive it
For SOUND4 to Dante :
- on SOUND4, select "AES67 Low Latency (Standard)" and chose a Multicast IP address that is free. Default port is 5004 if not given
- Check Stream format in Advanced/AES67 Profiles for "Sample Format" (normally L24) and "Nb Channels" (normally 2)
- stream should appear on Dante Controller, with a "+" drop-down to select channels. If no "+", SDP is not recognised.
- on Dante sink device you normally just have to configure this address and port if requested.
Note :
- Dante Controller only used for connection. Dante device is then "subscribed" to the stream (to the Mcast IP address) forever (no need Controller afterwards).
Tools
RAV2SAP
Translate Ravenna mDNS <=> Dante SAP
May be used to diagnose advertisement problems (SDP SAP)
https://www.ravenna-network.com/aes67/rav2sap/
Troubleshooting
S4->Dante
Advertised (checkmark under Dante Controller) but no sound (HP greyed) : check clock is AES67. If clock not synched, no sound.
